Carltsoe Safety CS Unitec Ex405-125A Aluminum Bronze Non-Sparking, Low-Magnetism, Corrosion Resistant Deck Scraper 5″ (125 mm) (405U-125A)

CS Unitec Ex405-125A Description

CS Unitec’s non-sparking, non-magnetic, corrosion-resistant safety hand tools are manufactured from special Aluminum-Bronze (AlBr) or Copper-Beryllium (CuBe2) alloys. All CS Unitec Safety Tools are backed by a lifetime warranty against defects in workmanship. If any CS Unitec safety tool breaks or fails to perform under normal use or service, it will be repaired or replaced at no charge.* CS Unitec safety tools are high quality manufactured in an ISO 9001:2015 environment and are TUV materials certified. They comply with ATEX Directives for Ex Zones 0, 1 and 2 (Flammable Gas, Mists or Vapors); Zones 20, 21 and 22 (Combustible Dusts); and M1 and M2 for mining. All hand tools are drop forged to produce the highest quality and durability. With over 4,000 SKUs offered, CS Unitec safety tools fit a wide range of applications. Non-Sparking applications include: Ex zones where hazardous, flammable or combustible vapors, liquids, dusts or residues may be present. Non-Magnetic applications include: MRI/NMR, nuclear products, electronic manufacturing, and other sensitive equipment. Corrosion resistant applications include: use in desalination plants, chemical/paper manufacturing, and shipyards. *Any misuse, abuse or normal service wear is not covered under this warranty.

CS Unitec Ex405-125A Includes

• (1) Scrapers Non-Sparking

CS Unitec Ex405-125A Features

• Non-Sparking, Non-Magnetic & Corrosion-Resistant Tools for Use in Hazardous Environments, ATEX and EX Zones
• Lifetime Warranty, ISO 9001:2015 manufactured, TUV certified
• Non-Sparking alloys are designed to eliminate the risk of sparks at sites where explosive atmospheres (flammable or combustible vapors, liquids, dusts or residues) may be present
• The non-magnetic feature of these hand tools also makes them ideal for working on MRI, FMRI, NMR, clean room environments and special machinery with powerful magnets. Copper Beryllium recommended for safer non-magnetic applications and around sensistive equipment.
• These corrosion-resistant tools are suitable for use in shipyards, laboratories, pharmaceutical, and food product manufacturing.
• Diagonal cutting pliers are designed for electrical, electronic, telephone, general and automotive work involving cutting and skinning wire, cutting and removing cotter pins, nails and other fasteners. Oil pliers occasionally. A drop of oil at the hinge will lengthen tool life and assure easy operation. Safety glasses should be worn when cutting wire, etc. to protect eyes from being struck by the end of the object being cut. WARNING: Ordinary plastic dipped handles are designed for comfort, not electrical insulation. Tools having high dielectric insulation are available and are so identified. Do not confuse the two.
• Pliers should not be used for cutting hardened wire unless specifically manufactured for this service. Never expose pliers to excessive heat. This may draw the temper and ruin the tool. Always cut at right angles. Never rock from side to side or bend the wire back and forth against the cutting blades. Don’t bend stiff wire with light pliers. Needle nose pliers can be damaged by using the tips to bend too large a wire. Use a sturdier tool. Never use pliers as a hammer nor hammer on the handles. They may crack or break, or blades may be nicked by such abuse. Never extend the length of handles to secure greater leverage. Use a larger pair of pliers or a bolt cutter. Pliers should not be used on nuts or bolts. A wrench will do the job better and with less risk of damage to the fastener.
• Not as durable as CuBe
• Low magnetism due to minimal ferrous components. Appropriate for non-critical non-magnetic applications

CS Unitec Ex405-125A Specifications